Computer Impulse and Momentum 19 The impulse-momentum theorem relates impulse, the average force applied to an object times
the length of time the force is applied, and the change in momentum of the object: Here we will only consider motion and forces along a single line. The average force
is the
average net force on the object, but in the case where one force dominates all others, it is
sufficient to use only the large force in calculations and analysis.
For this experiment, a dynamics cart will roll along a level track. Its momentum will change as it
reaches the end of an initially slack elastic tether cord, much like a horizontal bungee jump. The
tether will stretch and apply an increasing force until the cart stops. The cart then changes
direction and the tether will soon go slack. The force applied by the cord is measured by a Force
Sensor. The cart velocity throughout the motion is measured with a Motion Detector. Using
Logger Pro to find the average force during a time interval, you can test the impulse-momentum
theorem. OBJECTIVES
•
• Measure a cart’s momentum change and compare to the impulse it receives.
Compare average and peak forces in impulses. MATERIALS
Computer
Vernier computer interface
Logger Pro
Vernier Motion Detector
Vernier Force Sensor dynamics cart and track
clamp
elastic cord
string
500 g mass PRELIMINARY QUESTIONS
1. In a car collision, the driver’s body must change speed from a high value to zero. This is true
whether or not an airbag is used, so why use an airbag? How does it reduce injuries?
2. You want to close an open door by throwing either a 400 g lump of clay or a 400 g rubber
ball toward it. You can throw either object with the same speed, but they are different in that
Physics with Vernier 19 - 1 Computer 19
the rubber ball bounces off the door while the clay just sticks to the door. Which projectile
will apply the larger impulse to the door and be more likely to close it? PROCEDURE
1. Measure the mass of your dynamics cart and record the value in the data table.
2. Connect the Motion Detector to DIG/SONIC 1 of the interface. If the
Motion Detector has a switch, set it to Track. Connect the Force Sensor
to Channel 1 of the interface. If your Force Sensor has a range switch,
set it to 10 N.
3. Open the file “19 Impulse and Momentum” in the Physics with Vernier folder. Logger Pro
will plot the cart’s position and velocity vs. time, as well as the force applied by the Force
Sensor vs. time.
4. Calibrate the Force Sensor.
a. Choose Calibrate CH1: Dual Range Force from the Experiment menu. Click
.
b. Don’t apply any force to the Force Sensor. Enter a 0 (zero) in the Reading 1 field. Hold
the sensor vertically with the hook downward and wait for the reading shown for CH1 to
stabilize. Click
. This defines the zero force condition.
c. Hang the 500 g mass from the sensor. This applies a force of 4.9 N. Enter 4.9 in the
Reading 2 field, and after the reading shown for CH1 is stable, click
. Click
to close the calibration dialog.
5. Place the track on a level surface. Confirm that the track is level by placing the low-friction
cart on the track and releasing it from rest. It should not roll. If necessary, adjust the track.
6. Attach the elastic cord to the cart and then the cord to the string. Tie the string to the Force
Sensor a short distance away. Choose a string length so that the cart can roll freely with the
cord slack for most of the track length, but be stopped by the cord before it reaches the end of
the track. Clamp the Force Sensor so that the string and cord, when taut, are horizontal and in
line with the cart’s motion.
7. Place the Motion Detector beyond the other end of the track so that the detector has a clear
view of the cart’s motion along the entire track length. When the cord is stretched to
maximum extension the cart should not be closer than 0.15 m to the detector.
8. Click , select Force Sensor from the list, and click to zero the Force Sensor. 9. Practice releasing the cart so it rolls toward the Motion Detector, bounces gently, and returns
to your hand. The Force Sensor must not shift and the cart must stay on the track. Arrange
the cord and string so that when they are slack they do not interfere with the cart motion. You
may need to guide the string by hand, but be sure that you do not apply any force to the cart
or Force Sensor. Keep your hands away from between the cart and the Motion Detector.
10. Click
to take data; roll the cart and confirm that the Motion Detector detects the cart
throughout its travel. Inspect the force data. If the peak exceeds 10 N, then the applied force
is too large. Roll the cart with a lower initial speed. If the velocity graph has a flat area when
it crosses the time-axis, the Motion Detector was too close and the run should be repeated.
11. Once you have made a run with good position, velocity, and force graphs, analyze your data.
To test the impulse-momentum theorem, you need the velocity before and after the impulse.
Choose an interval corresponding to a time when the elastic was initially relaxed, and the cart
was moving at approximately constant speed away from the Force Sensor. Drag the mouse
pointer across this interval. Click the Statistics button, , and read the average velocity.
Record the value for the initial velocity vi in your data table 1. In the same manner, choose an
19 - 2 Physics with Vernier Impulse and Momentum
interval corresponding to a time when the elastic was again relaxed, and the cart was moving
at approximately constant speed toward the Force Sensor. Drag the mouse pointer across this
interval. Click the statistics button and read the average velocity. Record the value for the
final velocity vf in the same data table.
12. From the force vs. time graph calculate the time interval of the impulse. First, select
“Examine” from the “Analyze” menu. Then, position the pointer at the beginning and then at
the end of the period when the force was non-zero and record the times t1 and t2. The time
interval of the impulse is
"t = t 2 # t1 ! F(N) t1 t2 t(s) Δt
On the same force vs. time graph, drag across the impulse, to select the entire period when
the force was non-zero. Find the average value of the force by clicking the Statistics button
.
13. Perform a second trial by repeating Steps 10–12, record the information in data table 1.
14. Change the elastic material attached to the cart. Use a new material, or attach two elastic
bands side by side.
15. Repeat Steps 10–13, record the information in your data table. DATA TABLE 1
Mass of cart kg Trial Final
Velocity
vf Initial
Velocity
vi Average
Force
F Duration
of Impulse
Δt Impulse Elastic 1 (m/s) (m/s) (N) (s) (N⋅s) 1
2 Physics with Vernier 19 - 3 Computer 19
Trial Final
Velocity
vf Initial
Velocity
vi Average
Force
F Duration
of Impulse
Δt Impulse Elastic 2 (m/s) (m/s) (N) (s) (N⋅s) 1
2 DATA TABLE 2
Trial
Elastic 1 Impulse
FΔt
(N⋅s) Change in
momentum
(kg⋅m /s) or (N⋅s) % difference between Impulse
and Change in momentum
(N⋅s) 1
2
Elastic 2
1
2 ANALYSIS
As you write your report, when you summarize and discuss your results, be sure to also address
the following questions.
1. From the mass of the cart and change in velocity, determine the change in momentum as a
result of the impulse. Make this calculation for each trial and enter the values in the data table
2.
2. Determine the impulse for each trial from the average force and time interval values. Record
these values in the same data table 2.
3. If the impulse-momentum theorem is correct, the change in momentum will equal the
impulse for each trial. Experimental measurement errors, along with friction and shifting of
the track or Force Sensor, will keep the two from being exactly the same. One way to
compare the two is to find their percentage difference. Divide the difference between the two
values by the average of the two, and then multiply by 100%. How close are your values,
percentage-wise? Do your data support the impulse-momentum theorem?
4. Look at the shape of the last force vs. time graph. Is the peak value of the force significantly
different from the average force? Is there a way you could deliver the same impulse with a
much smaller force?
5. Revisit your answers to the Preliminary Questions in light of your work with the impulsemomentum theorem.
6. When you use different elastic materials, what changes occurred in the shapes of the graphs?
Is there a correlation between the type of material and the shape? 19 - 4 Physics with Vernier Impulse and Momentum
7. When you used a stiffer or tighter elastic material, what effect did this have on the duration
of the impulse? What effect did this have on the maximum size of the force? Can you
develop a general rule from these observations? Physics with Vernier 19 - 5

AccountingQueen

(3)

Status NEW Posted 05 Sep 2017 08:09 AM My Price 8.00

Hel-----------lo -----------Sir-----------/Ma-----------dam----------- T-----------han-----------k y-----------ou -----------for----------- us-----------ing----------- ou-----------r w-----------ebs-----------ite----------- an-----------d a-----------cqu-----------isi-----------tio-----------n o-----------f m-----------y p-----------ost-----------ed -----------sol-----------uti-----------on.----------- Pl-----------eas-----------e p-----------ing----------- me----------- on----------- ch-----------at -----------I a-----------m o-----------nli-----------ne -----------or -----------inb-----------ox -----------me -----------a m-----------ess-----------age----------- I -----------wil-----------l

Not Rated(0)

• Buy Answer